+- ChitownRC (https://www.chitownrc.com)
+-- Forum: Main Forums (https://www.chitownrc.com/forum-4.html)
+--- Forum: Bashers Forum (https://www.chitownrc.com/forum-11.html)
+--- Thread: SPortwerks Chaos for a steal!! (/thread-8053.html)
SPortwerks Chaos for a steal!! - Ponch - 12-08-2007
These are smaller... Maybe be able to get/make a hub adapter to run 2wd tires all around, that would look BA.
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-08-2007
hmm u sure? coulda sworn that guys were running 4wd buggy tires on half 8's maybe thats the crt.5?
SPortwerks Chaos for a steal!! - blktransam - 12-08-2007
bought one lol
SPortwerks Chaos for a steal!! - Ponch - 12-08-2007
"to all chaos owners: replace the clutch bell needle bearing with 3 4X7 bearings. sportwerks used a needle bearing to hold up the clutch bell. you know, the bearings that have little steel rollers encased in a plastic housing? yeah. I replaced the clutch bell bearings with 3 of them"
Mike, you're thinking CRT.5. They use 1/10 buggy rear tires.
SPortwerks Chaos for a steal!! - thenewguy821 - 12-08-2007
Also, check the clearance between the front outdrive and the fuel tank. When my son got one when they were first released, the outdrive would rub the fuel tank, wearing ALMOST through. A quick call to Horizon resulted in a free replacement tank AND outdrive shaft. This did seem to fix the problem.
The only other issue, was the fact that there is only one brake, which with a center diff, sometimes made for some tricky driving. Just lock the center diff and this problem will go away also.
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
Ok. so I was at Leisure today looking at two that had come in for service.
I was looking at the steering; it's pretty much the same setup as the 18t, which is prone to slop. Plus those tie rods were junk; there was so much play it wasn't even funny.
So I think if I were to get one, I would have to make a custom plate to fix the steering slop and tighten up the servo saver. Then, some actual turn buckles would be needed...
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
ponch what do u expect for 70$ from sportwerks?
SPortwerks Chaos for a steal!! - motoxer4life - 12-09-2007
Ponch Wrote:"to all chaos owners: replace the clutch bell needle bearing with 3 4X7 bearings. sportwerks used a needle bearing to hold up the clutch bell. you know, the bearings that have little steel rollers encased in a plastic housing? yeah. I replaced the clutch bell bearings with 3 of them"
Mike, you're thinking CRT.5. They use 1/10 buggy rear tires.
Matt u got a link of those bearings?
SPortwerks Chaos for a steal!! - motoxer4life - 12-09-2007
And you guys think 30% gas will be fine in these lil engines?
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
should be fine
SPortwerks Chaos for a steal!! - thenewguy821 - 12-09-2007
motoxer4life Wrote:And you guys think 30% gas will be fine in these lil engines?
Not a problem... That is what my son runs in his.
SPortwerks Chaos for a steal!! - motoxer4life - 12-09-2007
K sweet, hey has your son broken anything on his? Like are they pretty durable and all? And how about break in, should i just do the normal heat cycle?
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
Nick...
You need (4) (quantity) 4mm by 7mm bearings (dimensions)
Breakin-they say a tank... I would just go by traxxas breakin pretty much.
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
lol fire it up put it on a brick to keep the wheels off the ground pin it and open the HSN about 3 turns hold it pinned for a minute or so while the fuel pours out let off and lean it back down 3 turns and then race tune. LOL a p/s costs like 30$ just beat it up hhahaha
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
Nope- $20!!! haha
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
i would really imagine that that whole motor is idiot proof. With a price that cheap im sure the deck height is high so you could run liek 80% nitro, no breakin, temps at 400* and itd still last a long time. The average joe that never had a nitro treatment if you will lol
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
yeah it's a 1 needle carb too lol
I actually don't like them that much, pisses me off most of the time
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
i bet u could go through it do some port work, measure deck height, maybe find a real carb that fits and itd be a better motor, or spend that 200$ it would cost you on something worth while lol
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
yeah.
I was thinking about port & polish, b/c if I messed up, it'd be cheap to fix.
SPortwerks Chaos for a steal!! - mikeh - 12-09-2007
Mini-t tires fit on the stock rims if that helps any.
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
Mike you already get yours? or just read that.
Either way, that gets us WAY more tire options!!!
SPortwerks Chaos for a steal!! - chicagokenji - 12-09-2007
80-100 dollars?
They're 259.00 "buy it now"
Was the OP smoking crack on his first post?
click on the first link to ebay in the first post now.
SPortwerks Chaos for a steal!! - Czech-it-Out Graphics - 12-09-2007
maybe it changed, they are still 100$ at amain
SPortwerks Chaos for a steal!! - Ponch - 12-09-2007
So....Somebody just bought the last 10 of them on ebay for that price
SPortwerks Chaos for a steal!! - chicagokenji - 12-09-2007
Czech is right...still 99 on Amain.
That's less than they pay for them when they buy them from Horizon.
AMain lost their relationship with Great Planes/Hobbico and can't distribute their products anymore...it's kinda odd that now they are advertising a Horizon product for less than they pay for it.
Something is really weird about 99 dollar Chaos......Horizon has them listed as $359.00:
Horizon Hobby: 1/16 Chaos Nitro 4WD RTR Buggy by Sportwerks (SWK1400)