+- ChitownRC (https://www.chitownrc.com)
+-- Forum: Open Forums (https://www.chitownrc.com/forum-5.html)
+--- Forum: Multimedia (https://www.chitownrc.com/forum-15.html)
+--- Thread: Kanai II Truggy Buildup (/thread-3756.html)
Kanai II Truggy Buildup - rocco79 - 06-14-2006
My truggy was just as fast as my savage if not faster... I dont think a 2 speed adds that much on the top end... I think it just helps nitro engines build the torque they need down low with a lower ratio...
Im sure if you got those boas on youd be fine
Kanai II Truggy Buildup - cemeb4dk - 06-14-2006
Assuming you have a 46 tooth spur (stock kyosho) and a 16 tooth bell you are running a 2.8 ratio. Thats about 1.5 too low for runnign mt tires... I hope you have another $70 for a new clutch soon. Because you are going to smoke the clutch and over work your engine.....
But then again what do I know....LOL
Kanai II Truggy Buildup - snakebite46 - 06-14-2006
Quote:But then again what do I know....LOL
Well let's see.
1. You know where to shop for big hats.
2. You know how to get mad over someone leaving your sharpie out.
3. You know how to make R/C purchases without the wife knowing.
4. You know how to ride your tri-cycle when your drunk.
5. You know how to lay the power down !!!
6. You know how to embalm some fresh meat.
Kanai II Truggy Buildup - Czech-it-Out Graphics - 06-14-2006
Lmao
Kanai II Truggy Buildup - cemeb4dk - 06-14-2006
Laughing my ass off....
Good to have you back....
Using that as my sig line...
Kanai II Truggy Buildup - Ponch - 06-15-2006
cemeb4dk Wrote:Assuming you have a 46 tooth spur (stock kyosho) and a 16 tooth bell you are running a 2.8 ratio. Thats about 1.5 too low for runnign mt tires... I hope you have another $70 for a new clutch soon. Because you are going to smoke the clutch and over work your engine.....
But then again what do I know....LOL
Nuh unh!!! I got me some LSP ring and pinion gears so I can run this chit dude...:p:
Kanai II Truggy Buildup - cemeb4dk - 06-15-2006
LOL
That is the rario at your clutch.
Ask how many LSP drivers are running a 16t bell, and I bet zero. And we have your ring and pinions and a larger spur gear... I have a NR 528 and the most I ever ran was a 15.
But like I said before what do I know, just trying to save you some aggrevation but you obviously know more.... 8^)
So good luck!!!!!!!
Kanai II Truggy Buildup - Ponch - 06-15-2006
cemeb4dk Wrote:LOL
That is the rario at your clutch.
Ask how many LSP drivers are running a 16t bell, and I bet zero. And we have your ring and pinions and a larger spur gear... I have a NR 528 and the most I ever ran was a 15.
But like I said before what do I know, just trying to save you some aggrevation but you obviously know more.... 8^)
So good luck!!!!!!!
Alright then... You are talking about running a 15t with regular sized tires though, right? Right now all I have to run is the komodo LP's and they're tiny.
Kanai II Truggy Buildup - Racin' Ranger1 - 06-15-2006
when u go to the track get some vid of that thing.
Kanai II Truggy Buildup - Ponch - 06-15-2006
If I remember to. We're rolling up there around 6 and I want to run as much as possible before sundown.
Kanai II Truggy Buildup - kevinF - 06-15-2006
yeah if you do video tape it make sure you POST IT UP...
lol
Kanai II Truggy Buildup - Ponch - 06-15-2006
Hey, my foams came in! My boas are all glued up and ready to run tonight.
If I do take video, I'll post it up.
Kanai II Truggy Buildup - Ponch - 06-15-2006
Uh-oh. I had a run away. Got about 40ft and then re-gained power. Thankfully, it jumped a little curb and ended up in a person down the street's lawn, about a foot away from their SUV tire. That could have been bad. I don't know what could have went wrong though, everything that should be loc-tighted is, all plugs are secure in the receiver, and there's no binding w/ the servos in motion. Ideas? It ran fine afterwards, no glitches or anything.
Do you think that mabye the metal gears (clutch and spur) are causing interference?