ChitownRC › Main Forums › Racers Forum v
Will a T-15 work in a RC10GT?

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Will a T-15 work in a RC10GT?
RCDad Offline
Posting Freak
*****
Posts: 1,862
Threads: 237
Joined: Feb 2005
Reputation: 0
#1
09-29-2005, 09:46 PM
Yes/no?
Dad's Toy
Website Find
Reply
rocco79 Offline
Super Moderator
******
Posts: 13,181
Threads: 169
Joined: Jul 2004
Reputation: 0
#2
09-29-2005, 09:56 PM
I would think so.... Im not sure if the shaft off the would matter or not
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Find
Reply
bigjs Offline
Senior Member
****
Posts: 630
Threads: 32
Joined: Jun 2005
Reputation: 0
#3
09-29-2005, 10:08 PM
does the t-15 have a short shaft?
Kanai K3
Kanai K2
LSP-R project
Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#4
09-30-2005, 10:29 AM
T-15?
Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#5
09-30-2005, 10:50 AM
If you mean the mill that can with the original Tmaxx, then no it wont fit with out mods. The backplate and the flywheel on that engine is too big, it wont fit on any of the motor mounts avail. for the GT.
Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#6
09-30-2005, 10:53 AM
Except prob. the .21 motor mount for the GT from GPM!! I've thought about that one for a while...but drivetrain wouldn't last long at all.
Find
Reply
Tex Offline
Super Moderator
******
Posts: 9,001
Threads: 126
Joined: Jul 2004
Reputation: 0
#7
09-30-2005, 12:59 PM
again ......t-15???? is that the TTR or HPI motor?
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Find
Reply
RCDad Offline
Posting Freak
*****
Posts: 1,862
Threads: 237
Joined: Feb 2005
Reputation: 0
#8
09-30-2005, 01:51 PM
Hpi
Dad's Toy
Website Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#9
09-30-2005, 01:53 PM
Ohhhh!!
Find
Reply
Tex Offline
Super Moderator
******
Posts: 9,001
Threads: 126
Joined: Jul 2004
Reputation: 0
#10
09-30-2005, 02:00 PM
is it a short crank or a long crank?
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Find
Reply
RCDad Offline
Posting Freak
*****
Posts: 1,862
Threads: 237
Joined: Feb 2005
Reputation: 0
#11
09-30-2005, 02:11 PM
Shorter than the Associated .15
Dad's Toy
Website Find
Reply
Tex Offline
Super Moderator
******
Posts: 9,001
Threads: 126
Joined: Jul 2004
Reputation: 0
#12
09-30-2005, 04:51 PM
you could try a different flywheel nut with an extension on it.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Find
Reply
PoPRC Offline
Senior Member
****
Posts: 708
Threads: 34
Joined: Aug 2005
Reputation: 0
#13
09-30-2005, 05:45 PM
Go here RC10GT FORUMS These guys would probably know for sure. It's where I go if I need a GT question answered.
Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#14
09-30-2005, 05:47 PM
pop hows your gt running?
Find
Reply
PoPRC Offline
Senior Member
****
Posts: 708
Threads: 34
Joined: Aug 2005
Reputation: 0
#15
09-30-2005, 06:00 PM
Its doing well, I need to put some new tires on it (once I get some cash). I took it out to the DeVry spot about two weeks ago and lost a servo mounting bracket screw, replaced that. Then I took it to a park by my grandfathers house with my son and ran it for about an hour. We had like 10 kids chasing it around in circles. It was pretty funny trying to not crash into them. We are gonna take it back to the DeVry spot tomorrow or Sunday or both, wife permitting. To start really tuning it for power (I pick up a Duratrax Temp sensor Smile) and then see what she really can do! I was thinking I might take it out to Intense Raceway Sunday, but Im not sure I'll have time, plus I am alittle under the weather.
Find
Reply
maxximum_44 Offline
Posting Freak
*****
Posts: 1,378
Threads: 29
Joined: Jul 2005
Reputation: 0
#16
09-30-2005, 06:12 PM
Good to hear. we finally got my buds "Gt" going. turned out to be needle settings on the picco
just as I had suspected. Not very funny when a Manufacture gives you general needle settings for an expensive mill that are way out of the ballpark, Im glad we didn't ruin it.

Be sure to post if your going to Devry this weekend, I might join ya if I can get out.
Find
Reply
PoPRC Offline
Senior Member
****
Posts: 708
Threads: 34
Joined: Aug 2005
Reputation: 0
#17
09-30-2005, 06:44 PM
All right I'll do that, wouldnt mind somebody else to bash with. I'll post tomorrow morning first thing whether is a yay or a nay.
Find
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Would This Work? UE-Maxx 0 1,084 04-09-2006, 02:57 PM
Last Post: UE-Maxx
  Will this work for sealing an engine? RCDad 4 1,678 02-05-2006, 05:16 PM
Last Post: RCDad
  Will this work? Ponch 15 2,731 02-02-2006, 05:33 PM
Last Post: Ponch
  My ride and Airbrush work Biodragen 20 4,362 11-30-2005, 10:03 PM
Last Post: nitrosmoker
  rc10gt questions bigjs 10 2,756 10-22-2005, 04:20 PM
Last Post: PoPRC
  rc10gt clutch problems bigjs 5 2,362 08-13-2005, 09:01 AM
Last Post: Obsessive R/C
  Will T maxx shocks work on a stampede? bigdangerous 1 1,630 10-20-2004, 08:37 AM
Last Post: R/C Madman

Forum Jump:


Users browsing this thread: 1 Guest(s)