My Mayhem ST Project

[Biodragen]

What I have Modified on my Mayhem ST and a few more things to do yet.
The wheels in photos are not the ones going to be used.

OFNA Violator 9.5 Fuel tank
OFNA 053 pipe
Full bearings throughout
Mayhem Buggy wing and wingstay
Alum diff cases, Center Diff Mount, Servo mount, Servo tray stand offs
XTM 138.6 Rear dog bone
KP Racing Hard Anodized Ext 1-1/2 Chassis
KP Racing Hard Anodized FR/RR Shock Towers
KP Racing Hard Anodized Center Brace
Airtronics 94358z HT Steering Servo
JR 650 TH\Brake servo

---Still have to be mounted\painted\Modified more or waiting for part
Mayhem upgraded Chassis Stiffners in addition to Center Brace
OFNA 17mm Half Offset (28mm) White Dish Wheels From Jammin Truck
Panther Boa Tires -glued on rims
KMW Racing LSP 8mm Axle Upgrade - Modified again with a 45 chamfer on inside cup for more throw
KMW Racing Wheel Hubs 3/8 ext
Majestic LSP Body
Stock CVD Dog Bones modified by axle joint, Ground away some of the taper for more throw
Dynamite CVD Boots

Wheels are all glued up, Axles are all assembled and waiting for hubs to arrive.
Body is in route for delivery and still has to be painted
Chassis stiffners need a bit more modification before install
I still have to counter sink body post mounts.
I will also have to rig up something to use the old body until the new one is finished.
Soon to add the Mugen MBX 5 Wingstay braces

[maxximum_44]

Lookin good

[Biodragen]

Thanks,
I hope this will take care of some issues I was having. I am pretty confident it will.
I drove another members ride that was like this and it was exactly what I was looking for.

Next will be a Lipo pack and making it a bump start.

[DAVEC-NITRO-RS4]

It's the Blues Mobile!
Looks nice....

[kevinF]

sweet

[Obsessive R/C]

Very nice

[rocco79]

Get a prefilter ... You motor will thank you

[Czech-it-Out Graphics]

nice but whats the point of the big ass center brace?

[NitroNuisance]

Looks great... I hope the truck is finally (closer) to what you want.

What are you going to do with white wheels on that beautiful blue and black truck??

[Biodragen]

Get a prefilter ... You motor will thank you

I did have it on there and it gets in the way of the throttle linkage.
I will have to change them out more often I guess

[Biodragen]

nice but whats the point of the big ass center brace?

Well based of the old set up and this set up the chassis is actually more rigid and almost no flex.
Less flex verses with the old upgraded stiffners and I will be adding those too.

Before all this I was able to realy twist the chassis so I got the upgraded ones Kevin Mention and it helped.
This new one is even better.

[Biodragen]

Looks great... I hope the truck is finally (closer) to what you want.

What are you going to do with white wheels on that beautiful blue and black truck??

right now it is---driving it is another but after driving bruces I was heading in the direction I wanted.

As for the wheels---Ying and Yang on them

[Czech-it-Out Graphics]

i guess that works seems like a bit too much overkill, flex is usually a good thing lol

[Biodragen]

I would have thought so too but that was the reason I was going through clutch bearings.
The mesh was fine up until the flex and twisting. Once I made that stiffer my bearings lasted.
I am stil debating on adding the SW ones in to this at all. I will run it first and see.

I will be there on Saturday all day.

[Flipside]

I was wondering how I can get in touch with the guy who makes these chassis's for the mayhem st I have been searching for it for a while now and can't find a website or an email address. If you could tell me where you found it it would be great.

[Biodragen]

I looked back and I found this
[email protected]

I got him through Truggy Racers but the site is all hacked right now and I suggest not to log in.

Other than that - I dunno

[MX_KEVIN]

There have been a few questions on pricing and what comes with the kit so here is a little information on pricing.

The whole chassis kit will be $125, It comes with the chassis, front and rear towers, comes with front and rear center braces. I will be offering the rear dog bone for $10 more do too the fact its hard getting a large quantity from my local hobby store I wont be offering it with every kit. Chassis is also set up for a 150cc tank or stock 125cc tank.

Im taking orders for these kits now, I think this batch will go fast

Im going too make a few extra chassis too be sold by themselves here soon will keep you posted, they will be $60.

Rear dogbone
XTM #149791 138.6mm dogbone

Fuel tanK
#OFN40109 Ofna 150cc crt tank or violator

You can call my cell phone at 330-224-4848
You can email me at [email protected]
My paypal is [email protected]

Thanks Kevin

And hes finishing another batch in a week or so...

[rocco79]

Hack your makin parts!?!?!?

[MX_KEVIN]

No...That was cut and pasted from trug racers,com. He just happens to have the same awsome name.

[Ponch]

Niiiicce...

Edit; NVM, lol you aint making the stuff hahaa...

[rocco79]

No...That was cut and pasted from trug racers,com. He just happens to have the same awsome name.

Quite possibly the gayest thing ive ever heard you say