ChitownRC › Main Forums › Racers Forum v
.12tz

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linear Mode
.12tz
Meatwad Offline
Banned
Posts: 2,473
Threads: 88
Joined: Oct 2006
#7
06-05-2007, 08:00 PM
Needle Valve (aka High Speed Needle):1¾ open from closed position
per page 18 of manual.

Mixture Control Screw (aka Low Speed Needle):The head of the mixture
control screw is flush with the carb body per page 25 of manual.

Metering Needle: Head of metering needle screw is flush with the
ball link body per page 25 of manual.

i was 1/4 turn lean on top. and rich on the bottom and mid-range
Find
Reply


Messages In This Thread
.12tz - by Meatwad - 06-05-2007, 07:23 PM
.12tz - by Tex - 06-05-2007, 07:33 PM
.12tz - by Meatwad - 06-05-2007, 07:46 PM
.12tz - by Czech-it-Out Graphics - 06-05-2007, 07:48 PM
.12tz - by Meatwad - 06-05-2007, 07:49 PM
.12tz - by Czech-it-Out Graphics - 06-05-2007, 07:55 PM
.12tz - by Meatwad - 06-05-2007, 08:00 PM
.12tz - by hansarvin - 06-05-2007, 09:08 PM
.12tz - by Meatwad - 06-05-2007, 09:27 PM
.12tz - by J-Dub - 06-05-2007, 09:46 PM
.12tz - by MX_KEVIN - 06-05-2007, 11:12 PM
.12tz - by UE-Maxx - 06-05-2007, 11:24 PM
.12tz - by J-Dub - 06-06-2007, 12:30 AM
.12tz - by AddictedtoNITRO - 06-06-2007, 05:52 AM
.12tz - by rocco79 - 06-06-2007, 07:10 AM
.12tz - by Meatwad - 06-06-2007, 08:04 AM
.12tz - by Meatwad - 06-06-2007, 08:04 AM
.12tz - by hansarvin - 06-06-2007, 10:56 AM
.12tz - by Meatwad - 06-06-2007, 11:10 AM
.12tz - by Tex - 06-06-2007, 11:19 AM
.12tz - by Tex - 06-06-2007, 11:25 AM
.12tz - by Meatwad - 06-06-2007, 11:27 AM
.12tz - by MX_KEVIN - 06-06-2007, 12:03 PM
.12tz - by hansarvin - 06-06-2007, 12:45 PM
.12tz - by Meatwad - 06-06-2007, 12:46 PM
.12tz - by rocco79 - 06-06-2007, 04:34 PM
.12tz - by Meatwad - 06-06-2007, 04:56 PM
.12tz - by Czech-it-Out Graphics - 06-06-2007, 05:18 PM
.12tz - by NickGT - 06-06-2007, 08:17 PM
.12tz - by Meatwad - 06-06-2007, 08:20 PM

Forum Jump:


Users browsing this thread: 3 Guest(s)