ChitownRC › Main Forums › Racers Forum v
my new mill

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linear Mode
my new mill
cr4sh_27 Offline
Senior Member
****
Posts: 516
Threads: 22
Joined: Apr 2007
Reputation: 0
#24
08-27-2007, 01:18 AM
^^ well, im takin "care" of this motor just to see how long itll last. im doin stuff like movin the piston to BDC during cool down, after run oil after done runnin for the day, keepin it clean, i even installed an on-board thermometer to make sure i have it tuned correctly at all times,0 installed an in line fuel filter and three stage air filter.
so there shouldnt be any excuses why this thing wont last.

so if it does last....then this may be the engine that i buy from now on
Find
Reply


Messages In This Thread
my new mill - by cr4sh_27 - 08-25-2007, 10:22 PM
my new mill - by Thirdgen89GTA - 08-25-2007, 10:27 PM
my new mill - by cr4sh_27 - 08-25-2007, 10:31 PM
my new mill - by J-Dub - 08-25-2007, 10:39 PM
my new mill - by cr4sh_27 - 08-25-2007, 10:44 PM
my new mill - by motoxer4life - 08-25-2007, 11:06 PM
my new mill - by cr4sh_27 - 08-25-2007, 11:08 PM
my new mill - by cr4sh_27 - 08-25-2007, 11:13 PM
my new mill - by Thirdgen89GTA - 08-25-2007, 11:15 PM
my new mill - by motoxer4life - 08-25-2007, 11:17 PM
my new mill - by cr4sh_27 - 08-25-2007, 11:29 PM
my new mill - by J-Dub - 08-26-2007, 08:29 AM
my new mill - by cr4sh_27 - 08-26-2007, 08:30 AM
my new mill - by Czech-it-Out Graphics - 08-26-2007, 07:46 PM
my new mill - by J-Dub - 08-26-2007, 07:58 PM
my new mill - by Ponch - 08-26-2007, 08:22 PM
my new mill - by J-Dub - 08-26-2007, 08:25 PM
my new mill - by motoxer4life - 08-26-2007, 08:45 PM
my new mill - by J-Dub - 08-26-2007, 08:45 PM
my new mill - by motoxer4life - 08-26-2007, 08:48 PM
my new mill - by J-Dub - 08-26-2007, 08:49 PM
my new mill - by cr4sh_27 - 08-26-2007, 10:07 PM
my new mill - by J-Dub - 08-27-2007, 12:56 AM
my new mill - by cr4sh_27 - 08-27-2007, 01:18 AM
my new mill - by allan42r - 08-27-2007, 02:35 AM
my new mill - by Ponch - 08-27-2007, 07:19 AM
my new mill - by cr4sh_27 - 08-27-2007, 11:21 AM
my new mill - by Tex - 08-27-2007, 03:08 PM
my new mill - by cr4sh_27 - 08-27-2007, 08:00 PM
my new mill - by motoxer4life - 08-27-2007, 08:15 PM
my new mill - by kevinF - 08-27-2007, 08:40 PM
my new mill - by Czech-it-Out Graphics - 08-27-2007, 08:42 PM
my new mill - by chickenfarmer3 - 08-27-2007, 08:58 PM
my new mill - by Ponch - 08-27-2007, 09:01 PM
my new mill - by cr4sh_27 - 08-27-2007, 10:45 PM
my new mill - by Czech-it-Out Graphics - 08-27-2007, 10:49 PM
my new mill - by Ponch - 08-27-2007, 10:52 PM
my new mill - by cr4sh_27 - 08-27-2007, 10:57 PM
my new mill - by Czech-it-Out Graphics - 08-27-2007, 10:59 PM
my new mill - by cr4sh_27 - 08-27-2007, 11:01 PM
my new mill - by cheesecake - 08-27-2007, 11:20 PM
my new mill - by Ponch - 08-27-2007, 11:22 PM
my new mill - by Czech-it-Out Graphics - 08-27-2007, 11:25 PM
my new mill - by Ponch - 08-27-2007, 11:27 PM
my new mill - by cr4sh_27 - 08-27-2007, 11:29 PM
my new mill - by cheesecake - 08-27-2007, 11:45 PM
my new mill - by cr4sh_27 - 08-28-2007, 12:04 AM
my new mill - by J-Dub - 08-28-2007, 12:08 AM
my new mill - by cheesecake - 08-28-2007, 12:19 AM
my new mill - by cr4sh_27 - 08-28-2007, 12:20 AM
my new mill - by cheesecake - 08-28-2007, 12:21 AM
my new mill - by cr4sh_27 - 08-28-2007, 12:36 AM
my new mill - by J-Dub - 08-28-2007, 12:42 AM
my new mill - by cheesecake - 08-28-2007, 12:48 AM
my new mill - by motoxer4life - 08-28-2007, 06:28 AM
my new mill - by Ponch - 08-28-2007, 07:26 AM
my new mill - by allan42r - 08-28-2007, 11:36 AM
my new mill - by pwnzor - 08-28-2007, 11:37 AM
my new mill - by Czech-it-Out Graphics - 08-28-2007, 11:54 AM
my new mill - by allan42r - 08-28-2007, 12:06 PM
my new mill - by cheesecake - 08-28-2007, 01:23 PM
my new mill - by allan42r - 08-28-2007, 02:11 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  808 with a new mill and new pair of shoes. slaytanic 6 3,098 07-15-2008, 01:09 PM
Last Post: Czech-it-Out Graphics

Forum Jump:


Users browsing this thread: 3 Guest(s)