Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rc8
#10
Czech-it-Out Graphics Wrote:Im running the 1.3's; I think they are labeled on the parts tree that they come on it. Ive heard the 8 hole 1.3 kyosho pistons were the best. The pistons dont come on a tree so they dont have any rough edges. 35-30 should do u good at LH

well with the supers you get the 1.4 wich are marked and another set that arebnt markes so those must be 1.3 ill give those a try are you using the short rod ends also?
Confusedalute:Casterracingusa.com Confusedalute: TrueRC.comConfusedalute: Confusedalute:Fusionracingrc.com (Fusion Fluids) Confusedalute: Nitrotoyz.comConfusedalute:Thercshack.comConfusedalute:Fastlane-graphix.comConfusedalute:
Reply


Messages In This Thread
Rc8 - by Czech-it-Out Graphics - 06-16-2008, 06:41 PM
Rc8 - by chris arnold - 06-16-2008, 06:56 PM
Rc8 - by Czech-it-Out Graphics - 06-16-2008, 07:28 PM
Rc8 - by DAVEC-NITRO-RS4 - 06-16-2008, 07:51 PM
Rc8 - by Czech-it-Out Graphics - 06-16-2008, 09:37 PM
Rc8 - by cheesecake - 06-16-2008, 10:04 PM
Rc8 - by Czech-it-Out Graphics - 06-16-2008, 10:14 PM
Rc8 - by rocco79 - 06-16-2008, 10:23 PM
Rc8 - by Czech-it-Out Graphics - 06-16-2008, 10:28 PM
Rc8 - by cheesecake - 06-16-2008, 11:38 PM
Rc8 - by Czech-it-Out Graphics - 06-17-2008, 01:01 AM
Rc8 - by cheesecake - 06-17-2008, 01:14 AM
Rc8 - by Czech-it-Out Graphics - 06-17-2008, 02:03 AM
Rc8 - by rocco79 - 06-17-2008, 06:40 AM
Rc8 - by Czech-it-Out Graphics - 06-17-2008, 07:32 AM
Rc8 - by 1armed1 - 06-17-2008, 07:45 AM
Rc8 - by FreeRideFrosty - 06-17-2008, 08:36 AM
Rc8 - by Czech-it-Out Graphics - 06-17-2008, 09:28 AM
Rc8 - by chris arnold - 06-18-2008, 03:49 PM
Rc8 - by DAVEC-NITRO-RS4 - 06-18-2008, 04:24 PM
Rc8 - by Czech-it-Out Graphics - 06-18-2008, 04:54 PM
Rc8 - by slaytanic - 06-18-2008, 06:23 PM
Rc8 - by Czech-it-Out Graphics - 06-18-2008, 08:10 PM
Rc8 - by cheesecake - 06-18-2008, 08:13 PM
Rc8 - by Czech-it-Out Graphics - 06-18-2008, 08:24 PM
Rc8 - by cheesecake - 06-18-2008, 09:05 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)