ChitownRC › Main Forums › Racers Forum v
Gorilla or CNC

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linear Mode
Gorilla or CNC
Tex Offline
Super Moderator
******
Posts: 9,001
Threads: 126
Joined: Jul 2004
Reputation: 0
#8
02-17-2005, 09:41 AM
thenewguy821 Wrote:If you decide down the line to sell off the Maxx for a different truck, you can pull off the UE parts and get back almost what you paid for them.

you can actually get EXACTLY what you payed for them if you buy used. You only take a loss if you buy new.

Say you buy some used UE diffs for $185. You can use them and re-sell them again for $185.
Big Grin (granted you didn't run too many gallons through them and they are still in very good condition)
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Find
Reply


Messages In This Thread
Gorilla or CNC - by RCDad - 02-16-2005, 04:06 AM
Gorilla or CNC - by Tex - 02-16-2005, 11:27 AM
Gorilla or CNC - by Tex - 02-16-2005, 12:13 PM
Gorilla or CNC - by RCDad - 02-16-2005, 03:36 PM
Gorilla or CNC - by Tex - 02-16-2005, 04:03 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 12:00 AM
Gorilla or CNC - by RCDad - 02-17-2005, 04:10 AM
Gorilla or CNC - by Tex - 02-17-2005, 09:41 AM
Gorilla or CNC - by RCDad - 02-17-2005, 11:45 AM
Gorilla or CNC - by Tex - 02-17-2005, 11:59 AM
Gorilla or CNC - by Tex - 02-17-2005, 12:08 PM
Gorilla or CNC - by Tex - 02-17-2005, 12:10 PM
Gorilla or CNC - by RCDad - 02-17-2005, 12:11 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 12:29 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:02 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 01:19 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:30 PM
Gorilla or CNC - by Tex - 02-17-2005, 01:35 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:44 PM
Gorilla or CNC - by Tex - 02-17-2005, 02:26 PM
Gorilla or CNC - by RCDad - 02-17-2005, 04:18 PM
Gorilla or CNC - by RCDad - 02-17-2005, 04:26 PM
Gorilla or CNC - by Tex - 02-17-2005, 05:05 PM
Gorilla or CNC - by Tex - 02-17-2005, 05:09 PM
Gorilla or CNC - by RCDad - 02-17-2005, 06:15 PM
Gorilla or CNC - by Tex - 02-17-2005, 06:54 PM
Gorilla or CNC - by RCDad - 02-17-2005, 07:09 PM
Gorilla or CNC - by Tex - 02-17-2005, 07:34 PM
Gorilla or CNC - by RCDad - 02-17-2005, 07:45 PM
Gorilla or CNC - by Tex - 02-17-2005, 07:50 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)