Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Gorilla or CNC
#18
both suspensions are awesome for either. But yes, that is the general idea.

I run/race EXT.

Back to the quality comment, a crash that will fold a fastlane arm won't even phaze, much less dent a UE arm. It's comparring the apples to oranges.

Say you have fastlane and end up using their warranty on (4) arms. that's $32. I can almost guarrantee you will NEVER have to use UE's warranty. I've only seen UE stuff break once in person. That was a Sirio.23 powered predator full speed into a brick wall usinf racerX suspension.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply


Messages In This Thread
Gorilla or CNC - by RCDad - 02-16-2005, 04:06 AM
Gorilla or CNC - by Tex - 02-16-2005, 11:27 AM
Gorilla or CNC - by Tex - 02-16-2005, 12:13 PM
Gorilla or CNC - by RCDad - 02-16-2005, 03:36 PM
Gorilla or CNC - by Tex - 02-16-2005, 04:03 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 12:00 AM
Gorilla or CNC - by RCDad - 02-17-2005, 04:10 AM
Gorilla or CNC - by Tex - 02-17-2005, 09:41 AM
Gorilla or CNC - by RCDad - 02-17-2005, 11:45 AM
Gorilla or CNC - by Tex - 02-17-2005, 11:59 AM
Gorilla or CNC - by Tex - 02-17-2005, 12:08 PM
Gorilla or CNC - by Tex - 02-17-2005, 12:10 PM
Gorilla or CNC - by RCDad - 02-17-2005, 12:11 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 12:29 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:02 PM
Gorilla or CNC - by thenewguy821 - 02-17-2005, 01:19 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:30 PM
Gorilla or CNC - by Tex - 02-17-2005, 01:35 PM
Gorilla or CNC - by RCDad - 02-17-2005, 01:44 PM
Gorilla or CNC - by Tex - 02-17-2005, 02:26 PM
Gorilla or CNC - by RCDad - 02-17-2005, 04:18 PM
Gorilla or CNC - by RCDad - 02-17-2005, 04:26 PM
Gorilla or CNC - by Tex - 02-17-2005, 05:05 PM
Gorilla or CNC - by Tex - 02-17-2005, 05:09 PM
Gorilla or CNC - by RCDad - 02-17-2005, 06:15 PM
Gorilla or CNC - by Tex - 02-17-2005, 06:54 PM
Gorilla or CNC - by RCDad - 02-17-2005, 07:09 PM
Gorilla or CNC - by Tex - 02-17-2005, 07:34 PM
Gorilla or CNC - by RCDad - 02-17-2005, 07:45 PM
Gorilla or CNC - by Tex - 02-17-2005, 07:50 PM

Forum Jump:


Users browsing this thread: 2 Guest(s)