|
Stripped Engine Head Screws
|
12-17-2005, 02:23 PM
Well I was bored and didn't know what to do, so I thought that I would try and clean my cooling head. I was using duratrax hex drivers to take them out. I got 2 out, and on the last two the hex driver was spinning and the screw wasn't. I was like "great". How can I get those out?
FS-Sportwerks 1/8 Hauler
12-17-2005, 02:52 PM
UE-Maxx Wrote:Well I was bored and didn't know what to do, so I thought that I would try and clean my cooling head. I was using duratrax hex drivers to take them out. I got 2 out, and on the last two the hex driver was spinning and the screw wasn't. I was like "great". How can I get those out?The screw is stripped out or is the hex driver rounded off? Use J-B Weld and set the hex driver into the screw. Next day you can turn them out together, and then break the driver free from the screw and repeat on the other. Then use really good screws when you put it back together. 
12-17-2005, 03:02 PM
There is a product at sears you can use. Its a liquid with tiny tiny pieces of friction material in it.... You drip some of the product into the stripped screw and its supposed to give you 400% more gripping power on rounded off or stripped screw heads.
You could try to use a standard style (not metric) allen key somtimes the small increase in size is just enough to bust the fastener free. or......... Just leave them in and put the others back!!! LOL!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
12-17-2005, 04:18 PM
Thanks guys. The hex driver is rounded off. I will try a non-metric wrench first, and if that doesn't work I will go with the J-B Weld thing. Will the hex driver be easy to break free from the J-B Weld and the screw? I know that J-B Weld gets really hard.
FS-Sportwerks 1/8 Hauler
12-17-2005, 06:22 PM
Worst case if it doesn't, you need a new wrench and screw, but you needed those anyway.
12-17-2005, 08:01 PM
Quote:Worst case if it doesn't, you need a new wrench and screw, but you needed those anyway. I don't need new wrenches. I just got the Duratrax hex drivers. I didn't think about using a junk allen wrench to do it to.
FS-Sportwerks 1/8 Hauler
12-17-2005, 11:52 PM
yeah just use a junk allen key.. if the JB weld is really stuck break out a dremel and cut off the messed up piece of the allen key and its good to go again.
-- John --
1:1.. 01 Z28 Camaro A4 Sure.. its stock. 1:8's.. K3, Inferno GT, and a straight line beater car 1:18.. RC18t Mamba and 3s lipo 
12-18-2005, 12:36 AM
UE-Maxx Wrote:Thanks guys. The hex driver is rounded off. Sounds like you need new hex drivers that are strong?? Like Dave said :frog:
Mugen MBX5T
RBS5 RB2045 Futaba 3PM Hitec 5955, 5965 |
|
« Next Oldest | Next Newest »
|
| Possibly Related Threads… | |||||
| Thread | Author | Replies | Views | Last Post | |
| Would a 5HP engine fit in my buggy LMAO | Rawkfist_02 | 23 | 6,165 |
01-20-2008, 03:35 PM Last Post: J-Dub |
|
| Mugen Screws | slaytanic | 13 | 3,468 |
12-05-2007, 11:02 PM Last Post: slaytanic |
|
| Best engine for IGT? | slaytanic | 8 | 3,000 |
09-07-2007, 07:27 AM Last Post: slaytanic |
|
| Engine Sealing...:| | J-Dub | 20 | 4,903 |
08-29-2007, 06:08 PM Last Post: J-Dub |
|
| Which engine for an Inferno GT | Thirdgen89GTA | 25 | 5,133 |
04-05-2007, 11:33 PM Last Post: Tex |
|
| Engine help | motoxer4life | 10 | 2,507 |
01-26-2007, 04:43 PM Last Post: kevinF |
|
| Engine Disassembly | Rawkfist_02 | 27 | 5,101 |
01-13-2007, 09:23 PM Last Post: Czech-it-Out Graphics |
|
| Engine for 8ight | motoxer4life | 21 | 4,607 |
12-01-2006, 10:47 PM Last Post: rocco79 |
|
| Engine question: Novarossi or O.S. | motoxer4life | 21 | 4,259 |
11-29-2006, 10:44 PM Last Post: FreeRideFrosty |
|
| new engine for jammin x1 cr or crt kits | motoxer4life | 12 | 2,798 |
11-26-2006, 09:12 PM Last Post: rocco79 |
|
