+- ChitownRC (https://www.chitownrc.com)
+-- Forum: Main Forums (https://www.chitownrc.com/forum-4.html)
+--- Forum: Racers Forum (https://www.chitownrc.com/forum-9.html)
+--- Thread: T-maxx Help (/thread-2729.html)
T-maxx Help - maxximum_44 - 02-22-2006
or you can change your Clutch Bell.
*posted late*
T-maxx Help - Traxxas_Junkee - 02-22-2006
smaller is higher top speed and bigger is more punch (for spurs)
T-maxx Help - GWPHOENIX - 02-22-2006
I need to clear the doulbles in front if the stand. thats why i'm probibly
breaking my axles from being on the gas.
T-maxx Help - mikecooper - 02-22-2006
I just went to use my maxx after fixing the receiver problems, and it drove maybe 20 feet, then just revved, my spur gear is grinded down
now I have to buy a new one at Al's, that is if they have any, and find out how to replace the thing on the maxx.
T-maxx Help - Tex - 02-22-2006
GWPHOENIX Wrote:I need to clear the doulbles in front if the stand. thats why i'm probibly
breaking my axles from being on the gas.
ok, you know how you make that 90deg right turn right before that double at the top of that little hill. Mash the gas only when your whole rc makes it onto the downslope, don't gas it before that, make the full 90deg turn first. You'll clear it everytime.
T-maxx Help - kevinF - 02-22-2006
Tex Wrote:ok, you know how you make that 90deg right turn right before that double at the top of that little hill. Mash the gas only when your whole rc makes it onto the downslope, don't gas it before that, make the full 90deg turn first. You'll clear it everytime.
+1
T-maxx Help - UE-Maxx - 02-22-2006
Tex Wrote:ok, you know how you make that 90deg right turn right before that double at the top of that little hill. Mash the gas only when your whole rc makes it onto the downslope, don't gas it before that, make the full 90deg turn first. You'll clear it everytime.
Easy for you to say with a P5 in there.
J/K
T-maxx Help - Traxxas_Junkee - 02-22-2006
mikecooper Wrote:I just went to use my maxx after fixing the receiver problems, and it drove maybe 20 feet, then just revved, my spur gear is grinded down
You need to know how to replace it? Take the tank and motor off, the undo the nut take the gear off replace it, then put the motor and tank back in, take a piece of paper put it in between the spur gear and the clutch bell and gently push the motor towards the spur (center) Tighten down the motor screws on the bottom of the truck while still gently pushing the motor toward the spur, and then take the paper out and roll the truck to make sure that the mesh is good, if it is making like a grinding noise it is too tight, if it is super easy to roll it might be too loose you might want to move it a little bit to the center.
T-maxx Help - Tex - 02-22-2006
UE-Maxx Wrote:Easy for you to say with a P5 in there.
J/K
let me take yours for a spin next time we are there together. I'll show you the limits!
T-maxx Help - destroy_my_revo_15 - 02-22-2006
yea tex i would be glad to let ya take mine for a spin and see what ya think of it and where the good line is. of course ill have the 3.3 in it so just a fair warning...lol
T-maxx Help - mikecooper - 02-22-2006
Traxxas_Junkee Wrote:You need to know how to replace it? Take the tank and motor off, the undo the nut take the gear off replace it, then put the motor and tank back in, take a piece of paper put it in between the spur gear and the clutch bell and gently push the motor towards the spur (center) Tighten down the motor screws on the bottom of the truck while still gently pushing the motor toward the spur, and then take the paper out and roll the truck to make sure that the mesh is good, if it is making like a grinding noise it is too tight, if it is super easy to roll it might be too loose you might want to move it a little bit to the center.I found a tutorial online, and did it by that, it didn't have the paper technique, I got it all back together, and it seemed to spin fine, but I went to drive it and it revs high but goes slow, which way do I have to move the gears, closer together, or farther apart?
sorry I am new to this stuff.
T-maxx Help - Tex - 02-22-2006
sounds like your slipper is too loose. Tighten the slipper nut until fully tight, then back it off 1/4 turn.
T-maxx Help - Traxxas_Junkee - 02-22-2006
yeah, your mesh is find if the gears seem to be spinning ok, do what Tex said the slipper is to loose. You just didn't tighten the nut down as far as it should be.
T-maxx Help - mikecooper - 02-22-2006
is that the thing that is right after the spring? that is what you seem to be talking about, but not sure. also thanks for the help. I tried moving the mesh in and out
with no change, now I know why.
T-maxx Help - kevinF - 02-22-2006
yes, mike it is the nut right after the spring
T-maxx Help - mikecooper - 02-22-2006
ok thanks, I was ready to kick the damn thing off a cliff, I don't know how many times I changed the mesh closer and farther.
T-maxx Help - GWPHOENIX - 02-23-2006
TEX - i did try to mash the gas after the turn and the back nailed the second jump almost every time causing multiple flips.thats why i figured a gear change,sounds like i need a smaller spur for more bottom aceleration.but i did get6 a aftermarket pipe. i put up a pick after work.maybee it will give more bottom without changing gears
T-maxx Help - Traxxas_Junkee - 02-23-2006
Bigger spur gets more acceleration, and get the THS tmaxx pipe, gobs of low end torque
T-maxx Help - Tex - 02-23-2006
your truck didn't seem like it needed more power to me GWP. Seemed fine.
Yep a smaller spur will take power away from you and give you a higher top speed. If you want torque get an 18T CB.
If anyone wants me to take their RC for a spin to try and get things figured out setup wise, just LMK. It's hard for me to tell you what you should do without feeling the truck out for myself.
T-maxx Help - GWPHOENIX - 02-23-2006
i'm a bit confused?
i thought a smaller Cbell gives you more bottom/acellerartion.
a larger gives more top end
doesn't the same principal apply with the spur?
T-maxx Help - Michowski - 02-23-2006
GWPHOENIX Wrote:i'm a bit confused?
i thought a smaller Cbell gives you more bottom/acellerartion.
a larger gives more top end
doesn't the same principal apply with the spur?
For the spur gear its the opposite.
Bigger spur for more acceleration
smaller spur for more top end
bigger cb for more top end
smaller cb for more acceleration
T-maxx Help - DAVEC-NITRO-RS4 - 02-23-2006
Think ten speed bike gears.
T-maxx Help - GWPHOENIX - 02-23-2006
i understand now,thanks
T-maxx Help - maxximum_44 - 02-23-2006
Tex Wrote:your truck didn't seem like it needed more power to me GWP. Seemed fine.
Yep a smaller spur will take power away from you and give you a higher top speed. If you want torque get an 18T CB.
18T CB,Thats what I did. gonna test her out tonight
T-maxx Help - GWPHOENIX - 02-23-2006
i got 2 last ?'s
1. are revo and tmaxx cb and spur gears interchangable/will one work with the other/mesh up
2. what is the pro's and cons of this pipe/what efects will it have.
![[Image: wheel002.jpg]](http://i37.photobucket.com/albums/e66/gwphoenix/wheel002.jpg)