Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Airhogs Havoc Heli
#51
kevinF Wrote:put brand new regular AA's and try it agian, i can get 10-12 minutes easily

They were, he bought them along with the heli. I think his battery might need some more time on it, or it might just be a little bit of a dud.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#52
It's charging now and I'm gonna time it to see how long it runs for, but I know Matt's (Ponch's) got at least another 3-5 minute of flight.


His would still be able to climb good, mine would just hover a few inches off the ground and wouldn't go up.
8ight | Mini-T | CEN Boat | Stampede | JR R-1

ALL RC STUFF FOR SALE. PM FOR DETAILS.
Reply
#53
Yeah. THis new heli sucks ass. I get 4 minutes per charge of useable time (aka actually goes up/down). Hopefully some new batts will solve that, or off I go to WalMart again.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#54
Mine goes about 10 minutes on a charge. Also I put the thumbtack right in the nose, didn't hit the battery. As for it spinning wildly check the tail rotor or the little wing on the back it might be bent to one side.
IT'S ALL ABOUT THE PAIN; THE INK AND THE JEWELRY ARE JUST SOUVENIERS
Reply
#55
Yes it was the tail blade. And today ponch modded the shyt out of his heli, he cut alot of the foam away,and did a bunch more stuff to the main blades.
Reply
#56
I have been beating on it all day long! The kids just drove it like a rented mule. Now it only holds a charge for about 5 min, likely because the battery never got the 10 min rest between flights. Oh well. I got a 2 pack lazer tage set on the x-mas list!
You're never to old to be immature
Reply
#57
mikeh Wrote:I have been beating on it all day long!

:eek: :poke:
10/8/1871- the great Chicago fire. Approximately 250 people were killed in the fire; 98,500 people were left homeless; 17,450 buildings were destroyed along with the original Emancipation Proclamation.
Chicago Local 281, protecting lives and property for over 100 years.
Lawn sprinklers save your grass, Fire sprinklers save your a$$
Reply
#58
motoxer4life Wrote:Yes it was the tail blade. And today ponch modded the shyt out of his heli, he cut alot of the foam away,and did a bunch more stuff to the main blades.
I read that taking off to much foam makes it really hard to control and really wobbly in flight!

I've been using mine to piss off my dogs, they hate it because when they do finally get a hold of it, it bites them back!!!
IT'S ALL ABOUT THE PAIN; THE INK AND THE JEWELRY ARE JUST SOUVENIERS
Reply
#59
You're going places Tommy. Hahaha
Reply
#60
squirrel Wrote:I read that taking off to much foam makes it really hard to control and really wobbly in flight!

I've been using mine to piss off my dogs, they hate it because when they do finally get a hold of it, it bites them back!!!

Actually, his is alot smoother and flys straighter. I want to do that but i want the option of exchanging it too at walmart.
Reply
#61
Yep. I took a large chunk out of the back half of the body. Then I lowered the main rotor assy about 1/4 inch. I had to grind down the little metal shaft that the rotor rides on, and then I took off some plastic from the bottom of the rotor where the shaft goes in so it can sit lower without hitting the big gear. Quiet as HELL and has more steering, rises faster, got slightly longer runtimes too I bet.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#62
what are titty sprinkles?! LoL!!!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#63
Ask Cartman lol
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#64
Ponch Wrote:Yep. I took a large chunk out of the back half of the body. Then I lowered the main rotor assy about 1/4 inch. I had to grind down the little metal shaft that the rotor rides on, and then I took off some plastic from the bottom of the rotor where the shaft goes in so it can sit lower without hitting the big gear. Quiet as HELL and has more steering, rises faster, got slightly longer runtimes too I bet.


HAHAHAHA!!! I knew it. Now.... Pics.
Reply
#65
Where can I get spare parts for mine? The props are trashed.
Reply
#66
You can return it, or look on ebay.

If you look on ebay, look for Picooz Picoo Z Piccoz Picco Z Havoc

All will return stuff... All the same thing.

If it's that top prop thingy thats F'd and all it is is a chip on the edge, ask KevinF how he dremeled his. It worked great after, but I didn't quite pay attention to what he did all that well.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#67
havoc rotor, Radio Control, Toys Hobbies items on eBay.com

There Smile
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#68
Me and my bro exchanged ours today, brand new ones.
Reply
#69
$25 at Target today....Christmas present for the kids. shhhh.
got paint?
Colors by Dave - CBD
1-29-07 ... you know.
Reply
#70
24.74 everyday at wally mart or so my kids wish book says
LOVE AMERICA OR GET THE HELL OUT!
www.Suburbanchicagorockcrawlers.com
www.Keyknivesonline.com
www.rcslot.com
rc crawling headquarters and great customer support!
Reply
#71
Black Friday Ads 2007 - AirHogs R/C Havoc Heli at Target
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#72
Looks like we'll have 2! one for parts!
got paint?
Colors by Dave - CBD
1-29-07 ... you know.
Reply
#73
Mine is for sale at LH this Sunday $12
Thanks to:
Go Tech Engines http://www.racefactorindustries.com
Merlin Glow Plugs http://www.merlinglowplugs.com
Vantage Racing http://www.vantageracing.com
Torco RC Racing Fuels http://www.torco.com
Reply
#74
What's the catche....
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#75
Damnit, thats $10 i coulda spent on my new 5r! Maybe ill take mine back and exchange it for the $15??? Think theyll allow it?
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  What are some good winter rc heli flying tips? dealrocker 1 3,762 01-06-2010, 06:07 PM
Last Post: stratcat
  blade cx2 heli for sale 140 .00 eraser 0 3,610 12-30-2007, 01:00 PM
Last Post: eraser
  blade cx2 heli for sale eraser 2 4,231 12-06-2007, 07:30 AM
Last Post: briyouu
  New heli t to the maxx2 25 12,710 11-22-2007, 12:41 PM
Last Post: DAVEC-NITRO-RS4

Forum Jump:


Users browsing this thread: 2 Guest(s)