Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rapdily Wearing clutch shoes
#1
I switched to Carbon shoes after wearing out my alum shoes. I however didn't realize that the Alum shoes were worn, as they had the snap they had when new and weren't slippinf resulting in a nice spring gouge in my clutch bell./ The carbons I had wore out, well, almost out, in about 5-6 tanks. My presumption is to replace the clutch bell. Im going to assume I'm right.
LSP lots of Khz, Werks .28 8 port.

Revo 2.5, TRX 3.3 Engine, Center Diff. Fast and Turns on a dime.
Reply
#2
Don't you always assume that you're right?



For once you are. There's metallic particles engrained in the cb from the Alu shoes. I remember that some guys would soak the used cb's in something (cant remember what, some kind of solvent) that would remove the aluminum but leave the clutch bell in tact.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Reply
#3
Yeah, I'll have to look into that for my next clutch. I got a big groove in it right now from the springs, I think that isn't such a problem as that aluminium residue.
LSP lots of Khz, Werks .28 8 port.

Revo 2.5, TRX 3.3 Engine, Center Diff. Fast and Turns on a dime.
Reply
#4
Im not sure what your running carbon in but i find that high traction = short life for the carbon shoes. No carbon indoors @ LH or outdoors on pavement. Id only run them on a blown out no traction track like last year at LH outdoor track. (J/K)
I do however run the Forlonie(sp?)carbon slider on both buggy and truggy with VZB's all the time indoors and out and have not worn them out yet...Many gallons on them. Doesnt hit as hard as aluminum but lasts forever and when I have to pay full price for all my parts, long life is what im looking for.

MBX5T - O.S.
MBX5R - Novarossi
Nomadio
Reply
#5
fioroni retard sheesh
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#6
Well, the weird part is Mike L and Bernie both run the carbons and have no problems. me however I'm smoking them
LSP lots of Khz, Werks .28 8 port.

Revo 2.5, TRX 3.3 Engine, Center Diff. Fast and Turns on a dime.
Reply
#7
You can run them indoor, I know I used to do it all the time until I started running the M2C clutches. Make sure you blow out your clutch bearings so your shit doesnt slip. Most carbon shoes wont last you more than a gallon
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#8
5 tanks s a little less than normal I think LOL
LSP lots of Khz, Werks .28 8 port.

Revo 2.5, TRX 3.3 Engine, Center Diff. Fast and Turns on a dime.
Reply
#9
ive been running the mip 3 shoe on and off im going on a gallon and a half on the clutch so far i like it i ran it indoors most of the winter then ran it outdoors and it did ok outdoors
Confusedalute:Casterracingusa.com Confusedalute: TrueRC.comConfusedalute: Confusedalute:Fusionracingrc.com (Fusion Fluids) Confusedalute: Nitrotoyz.comConfusedalute:Thercshack.comConfusedalute:Fastlane-graphix.comConfusedalute:
Reply
#10
I'm just going to switch back to aluminium
Lasted be about 1.5 Gallons
LSP lots of Khz, Werks .28 8 port.

Revo 2.5, TRX 3.3 Engine, Center Diff. Fast and Turns on a dime.
Reply
#11
i say give the mip a try it has a completely different engagement then the other clutch setups ive tried it kind of gives it a electric feel when on and off the throttle more responsive would be the what im trying to say lol
Confusedalute:Casterracingusa.com Confusedalute: TrueRC.comConfusedalute: Confusedalute:Fusionracingrc.com (Fusion Fluids) Confusedalute: Nitrotoyz.comConfusedalute:Thercshack.comConfusedalute:Fastlane-graphix.comConfusedalute:
Reply
#12
the MIP isnt your traditional carbon clutch, you will get alot of miles out of that.
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  808 with a new mill and new pair of shoes. slaytanic 6 3,124 07-15-2008, 01:09 PM
Last Post: Czech-it-Out Graphics
  Setting up a clutch for 1/8th buggy Toughtrax 6 2,242 12-22-2007, 10:20 PM
Last Post: Czech-it-Out Graphics
  May need to borrow a clutch..... FreeRideFrosty 47 7,637 03-13-2007, 10:12 AM
Last Post: FreeRideFrosty
  Clutch Questions FreeRideFrosty 96 15,040 03-09-2007, 10:16 PM
Last Post: UE-Maxx
  Peak Racing 6-shoe Clutch?? FreeRideFrosty 4 1,557 02-19-2007, 03:11 AM
Last Post: Czech-it-Out Graphics
  Check out this clutch breakage on my 3.3! Mr. Tune 11 2,359 07-02-2006, 12:30 AM
Last Post: rocco79
  Revo Clutch Conversion? NitroNuisance 12 3,024 05-29-2006, 07:56 PM
Last Post: Tex
  OFNA OB4 PRO clutch issues... Thirdgen89GTA 9 2,693 03-17-2006, 02:19 PM
Last Post: Tex
  Mip Clutch For Revo Sh1nn3r 11 3,052 01-20-2006, 11:32 PM
Last Post: satoch
  Clutch Bearings? MX_KEVIN 23 4,234 12-30-2005, 11:51 AM
Last Post: BlackWolf42

Forum Jump:


Users browsing this thread: 1 Guest(s)