Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
general revo discussion
destroy_my_revo_15 Wrote:i need help! i cant keep my truck running. i can run it to top speed then when i go to turn around it goes to low rpms and dies. if anyone can help me that would be great cause im going to lh tomorrow to race so i need a quick fix

Turn up the idle. And a new plug....
Reply
thanks dave. after being mad for a while i figured that "hey i should go back to factory settings and go from there. truck is running stronger than ever. its a good thing i got a few spare plugs today :lol:
Reply
ok im still having the same problems just not as bad. i ruled out the lsn cause i did the pinch test and it dies out around 2-3 seconds. so could it be my idle? if so what should i do. i kno there is a certain mm that it has to be but i cant realli eyeball millimeters and i cant measure it with anything. any help will be appreciated.
Reply
Sounds to me like the truck is too lean. This is what I would do: Richen the HSN until the truck is noticably slow (really slow) then gradually lean the HSN from there in 1hr increments until your power comes back.
If it's lean..... richen it
If it's rich....lean it!
That's what I do to make it run good. Smile
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
well its running much better than before. i did richen it a little. i messed with the idle. it only died once after all of this.
Reply
I will get pics up of my progress tomorrow... I have some silicone drying. I did the single servo conversion, got the teckno throttle servo mount, and shaved the reciever box... a lot. I took off the roll hoop and cut off the front 1/3 of my Ti skid. I moved some crap around and it looks a lot lighter and cleaner than before. (My wing is a tad crooked but for a total of $18 I am very happy....)
Reply
since ive been hearing alot about the os 18tm and there short motor life would it be better to buy a new p/s for the trx 2.5r and get it modded or get it modded right now (aprox. 4 gals on it.)
Reply
Honestly I would do the motor swap or buy one of e-bay so that you have a brand new one to get modded. Then just save yours as a backup. It would be just a tad more expensive...
Reply
so if i do get the p/s should i get a crank too?
Reply
That I don't know... but wouldn't that all be close to the price of the motor swap or a new one on the bay??
Reply
Better yet get the XTM .18 off of ebay for $60...
Reply
umm if you get a super steal you can find the p/s for $50 shipped and idk how much the crank costs definately less than the trade in or a new one on ebay tho
Reply
I used run the os .18's and there fantastic motors while they last. But because you can only get about 3 gallons im going back to the 2.5r. That motor rips as well and is an awesome motor for just being a .15
[Image: mich1iy1.jpg]
Reply
That XTM .18 is a nice cheap upgrade for the Revo. Jesse Wolkenheim was running it saturday and the thing rips. He told me that it had a good power band. Little weak on the low but nice top end. Can't beat it for 60 bones.
Reply
Ive had great luck with Xtm engines also.
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
Im thinking about getting a os 18 tz
Mugen MBX5T Prospec
RB C6bb/O.S. Speed
Hitec 5955
Futaba s9351
Jr Z-1
http://www.frontlinetec.com

Soo easy a cave man can drive it Mooooooooooogen
Reply
I hear mixed reviews about the TZ. Mich and Satoch both ran TZ's for abit and would better answer your questions about them.
Reply
For me all it had over a tm was slightly more top end. Definatly get rid of the rotary carb because the engine has a hard time idling. In order to make it work you need to do a lot of work like moving the trans forward, making your own linkage, buy a 1/8th clutch to get best results with the motor. Il personally never run a tz in my revo again. A lot of work for very little results.
[Image: mich1iy1.jpg]
Reply
Hey guys, I'm messing with my M11 and was wondering if the only way to activate reverse is with the dial? If so, then I can assume it's safe to remove the optidrive since switching into reverse is no longer as easy as tapping a button.
Reply
A lot of people don't use the sensor and just wait for it to come to a complete stop. I did a FOC so I don't need to worry about it at all...
Reply
All the buttons on the M11 are mapable. You should be able to use any of them to switch the third channel.

The only thing optidrive does is wait until the truck is stopped before it actually switches into reverse. If you were to take it out and hit reverse before you stopped, it would try to switch into it. That can cause breakage real fast. IMO, optidrive is not needed.

Hell, reverse isn't needed either. Get yourself the FOC and remove everything that involves reverse. Then you will have one less thing on the truck that can break Smile.
Reply
I already picked up the FOC in the event I decide to get rid of reverse. For what I do with the truck I'm not ready to go the whole racer setup and reverse is handy when backyard bashing. I do think I will remove the optidrive tonight and leave reverse set with the dial.
Reply
Anybody planning on running the extended/adjustable Revo arms? I have them on backorder from Tower who are now saying late January...Ughhh!
Reply
I am going to give them a shot when they come out (and available at Leisure)
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
I may pick them up when Al's gets them. Depends on cash availability at the time. Gabe I can see you needing them. With that power any length will help...
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  E-Revo Brushless Edition? Summit? J-Dub 2 3,543 10-26-2008, 08:23 AM
Last Post: Fastlane GraphiX
  Batteries for stock e revo ricketki 4 6,177 08-05-2008, 06:40 PM
Last Post: BJoe
  Tower hobbies is giving away Platnium REVO's! Whoo Hoo! team3six 20 6,777 04-03-2008, 06:20 PM
Last Post: Toughtrax
  Revo, a race truggy? snoracer 61 14,297 02-13-2008, 05:27 PM
Last Post: J-Dub
  Traxxas Revo.... J-Dub 42 8,601 11-10-2007, 08:41 PM
Last Post: Michowski
  Quick Revo Diff question stratcat 12 3,538 08-10-2007, 04:55 PM
Last Post: DAVEC-NITRO-RS4
  Revo? Whitey04 33 7,197 05-27-2007, 09:00 PM
Last Post: J-Dub
  vantage one-way axle for 3.3 revo Meatwad 5 2,415 05-21-2007, 09:25 PM
Last Post: hansarvin
  Revo 3.3 Setup SEEKandDESTROY2 10 2,932 03-16-2007, 07:56 AM
Last Post: chickenfarmer3
  Project Darth Revo has begun... Mr. Tune 237 39,654 01-28-2007, 11:05 PM
Last Post: snakebite46

Forum Jump:


Users browsing this thread: 1 Guest(s)