Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
I need a new motor--
#51
Looks like this took a cruddy turn based on the posts.

Anyway This is where I am at with motors---I know you guys mentioned a few and that NR-528 I would have jumped on . That is out of range for cost for me.

So this is what I have looked into so far.

SW 26 w\o pull start
Type: 2-stroke
Displacement: .26 (4.26 cc)
Bore: 18mm (.71 in)
Stroke: 16.75mm (.66 in)
Engine (Only) Weight: 16.2 oz
RPM Range: 33,000
HP: 2.75
Cylinder Type: ABC
Starting System: Pull Start
Carb Type: Slide
Crank Type: SG


Picco 27 w\pull start
CLAIMED HP 3.1
RPM 34,000
CARB TYPE SLIDE
CRANK SG/Threaded
CONSTRUCTION ABC
ENGINE CASE SIZE .21
ENGINE BORE SIZE .27
TYPE REAR EXHAUST
PORTS 8 ports
DISPLACEMENT .27 c.i., 16.8 stroke
CRANKSHAFT Heavy Duty Crankshaft 14mm
CARBURETOR Composite, 8mm insert, changeable
PLUG TYPE Standard


Orion Wasp .28
• Horsepower: 2.85
• RPM (max): 42,800
• Carburetor: 2-Needle Slide
• Crank: Standard SG
• Engine bore size: 18.8mm
• Exhaust: Rear
• Stroke: 16.5mm
• ABC piston/sleeve
• Turbo design race ported crank
• Knife-edge double bushing connecting rod
• High performance 8mm aluminum slide carburetor
• Skirted / double oil groove piston design
• 3 transfer, 1 exhaust race spec porting configuration
• 2-piece replaceable button style Turbo head
• 6 bolt / 12 fin head configuration
• Sleeve locating pin for precise port alignment


Collari WRXLC30MT
3-port ABC constructed sleeve, coupled with the new "split-transfer" port case.
The connecting rod has been strengthened to be able to handle the rigors of greater horsepower.
It also has a fluted crankshaft and oversized pullstart one-way and shaft.
3.5HP 36,000RPM


Collari WRXLC32MTR Out of the box the crankshaft features chamfered timing inlets and a fluted counter-balance.
oversized cooling head and an 8.5mm aluminum carburetor that features a bullet-proof steel slide.
Standard dogbone drive roto-start included. 3.65HP 36,000RPM


Racers Edge Sure Fire .32 8-port
Horsepower: 3.6
RPM: 38,000
Engine Size: .32 cubic inch (5.2cc)
Sleeve: 8 port
Bore: 19.5 mm
Stroke: 17.5 mm
Crank: SG Type
Construction: ABC
Weight: 450 g (w/pull start)
Carburetor: 9 mm composite slide (with 8.5mm & 8 mm Carburetor reducers)
Carburetor adjustments: 3 needle, easy flush setting
Connecting rod: 7075 aluminum (Dual bushing)
Exhaust Type: Rear
Plug Type: Standard
Starting: Pullstart included



Right now I use the SW Rotostart an I would hope to use it ---I do not have a bump box nor do I care for the P\S set up.

So what is the census based on what I looked into.
Life is like Beavers, One Damn thing after another- Unknown
If your not breakin parts your not going fast enough-Biodragen


NTC3 RTR assoc .15
NTC3 OS .18

Losi 8T, JR8611a ST servo, Futaba 9350 Th\Brk Servo, RB-C6BB Motor and Novarossi 528XR.
Reply
#52
Id go with the 1st one you listed. The rest are not the best for racing, more basher motors. And i dont think the .32 is really even legal to race at a pro series event... I think

RUN from the wasp 28!!!!!!!!!!!!!!!!!!!!!!!!!!!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#53
I've heard quite a mix of reports on the Wasp .28, from Hard to Tune, Unreliable, doesn't hold a tune, to it being a great motor.

The SW .26 is really a good motor for the money. I had 6 gallons through a Mach .26 which is the same motor, with a different carb, and was still running strong when I sold it.

If you go with the SW, use the largest carb insert, you will deffinately notice the power increase.
Reply
#54
Oh yeah I forgot about the inserts.
The Mach 26 is that a Dynamite or a Assoc motor?
Life is like Beavers, One Damn thing after another- Unknown
If your not breakin parts your not going fast enough-Biodragen


NTC3 RTR assoc .15
NTC3 OS .18

Losi 8T, JR8611a ST servo, Futaba 9350 Th\Brk Servo, RB-C6BB Motor and Novarossi 528XR.
Reply
#55
Mach .26 is a Dynamite. If you look at the Engine, it's exactly like the SW, without the removable inserts for the Carb. The carb has the same opening as the middle size SW insert. The SW .26, Dynamite Mach .26, SH .28 and XTM 24.7 are all made by the same company.
Reply
#56
I would go with the first thing on the list also.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  GV Shark 4WD 1/10 - Powerfull motor installed but power lost in transmition system Antreas 1 3,701 12-09-2010, 10:08 AM
Last Post: Antreas
  motor liam 9 3,379 01-27-2008, 03:57 PM
Last Post: DAVEC-NITRO-RS4
  What Motor? snoracer 42 9,757 01-20-2008, 08:37 PM
Last Post: Eddie F
  Best Motor, ESC, servo for on-road? mikeh 6 2,455 06-15-2007, 03:42 PM
Last Post: Ponch
  T4RS Motor Moves forward BobWoodhouse 4 1,967 03-26-2007, 03:44 PM
Last Post: chris arnold
  Truggy Motor FreeRideFrosty 57 11,638 01-18-2007, 06:32 AM
Last Post: pwnzor
  New Sirio Motor for Revo (S27RE)!!! BAMF90 15 5,850 01-16-2007, 12:38 AM
Last Post: Czech-it-Out Graphics
  mid motor micro-t?!? thenewguy jr 1 1,472 01-09-2007, 07:30 PM
Last Post: squirrel
  Need Motor Reccomendations FreeRideFrosty 9 2,836 01-06-2007, 10:57 PM
Last Post: FreeRideFrosty
  whats the best motor?? Redwings 7 2,262 12-11-2006, 12:44 AM
Last Post: Redwings

Forum Jump:


Users browsing this thread: 3 Guest(s)