Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
WANTED!! Clutch
#1
It has been reccomended to me that I go with an 1/8th scale clutch instead of messing around with others. Let me know what you have and exactly how CHEAP I can get it for. LoL Thanks so much... (This will be going on th OS .21 VZ-B for those of you who didn't know.)
Reply
#2
you just need bearings and I have everything else including the bell for $4
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#3
I will run to Al's to get the conversion, the bearings (What size do I need??) and the 3 shoe flywheel... any specific one???
Reply
#4
I usually get the ofna 3 shoe flywheels (they make an OS specific one) they sit a bit further back to give you more clearance.

bearings are 5x10's, I've been running the "budget" bocas ($1 a piece) for about 3 gallons/5 months. Same set still work perfect

make sure to get the traxxas BB kit (there are a few to choose from) because it comes with the throttle bellcrank standoff you need. We will custom make your linkage at my house.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#5
Hey I would get the OFNA clutch shim kit to.

I did this on mine and it helps.
There are a few tiny little washers in there and they are thin.
Put the ones that are closest to the flywheel pins size on before the shoes.
This will keep the shoes from dragging on the flywheel.

Keeps the friction from the shoes wearing on the flywheel leaving it to move more freely.

this was a tip from some place I can't remember.
Life is like Beavers, One Damn thing after another- Unknown
If your not breakin parts your not going fast enough-Biodragen


NTC3 RTR assoc .15
NTC3 OS .18

Losi 8T, JR8611a ST servo, Futaba 9350 Th\Brk Servo, RB-C6BB Motor and Novarossi 528XR.
Reply
#6
AWESOME!!! Thanks so much... I don't need to drag my whole starter box contraption over do I?? Need a dremel??
Reply
#7
yep, grab that shim kit too, good call Biodragen
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#8
nope, no need for the starter box or dremel, although some sanding drums and cut off wheels would be good to have. That's what we'll use to trim out the chassis (if you plan on staying over a few hours)
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#9
Never mind... what is the earliest you want me to show up???
Reply
#10
call me if Al's doesn't have what you need I may have it. (Like shims for instance)
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#11
Yo free ride answer your pm
i can meet you at montini
Mugen MBX5T Prospec
RB C6bb/O.S. Speed
Hitec 5955
Futaba s9351
Jr Z-1
http://www.frontlinetec.com

Soo easy a cave man can drive it Mooooooooooogen
Reply
#12
like 5pm at the earliest.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#13
Sh1nn3r Wrote:Yo free ride answer your pm
i can meet you at montini


I was getting ready to call you. I will be there at 4.
Reply
#14
Aight ill see you there at 4 meet in the back parking lot kind by the baseball field.
Mugen MBX5T Prospec
RB C6bb/O.S. Speed
Hitec 5955
Futaba s9351
Jr Z-1
http://www.frontlinetec.com

Soo easy a cave man can drive it Mooooooooooogen
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Wanted: EMAXX chicagokenji 0 1,929 12-20-2010, 01:34 PM
Last Post: chicagokenji
  Slash or Crawler wanted TexMexSu 3 2,882 12-14-2010, 09:38 PM
Last Post: TexMexSu
  Wanted bargen 2.4g radio reciver spazzzattak 1 2,002 02-25-2010, 01:33 PM
Last Post: firesprink281
  Wanted trade/buy 3.3 tmaxx tranny spazzzattak 0 1,823 02-19-2010, 02:40 PM
Last Post: spazzzattak
  clutch bells grim digger 0 1,672 10-06-2009, 11:27 AM
Last Post: grim digger
  Wanted R/C 4wd 1/10 or 1/8 scale rednotch88 14 4,687 06-01-2009, 03:37 PM
Last Post: Astro
  Wanted Astro 1 1,555 04-25-2009, 02:45 PM
Last Post: Astro
  Wanted 5R... Ponch 14 3,852 08-28-2007, 09:41 AM
Last Post: Tex
  IPOD wanted! Sh1nn3r 1 1,571 08-25-2007, 12:34 PM
Last Post: nitrodude
  wanted laptop HDD Racin' Ranger1 4 1,779 08-14-2007, 10:36 PM
Last Post: Traxxas_Junkee

Forum Jump:


Users browsing this thread: 1 Guest(s)