Posts: 23
Threads: 7
Joined: Jul 2006
Reputation:
0
Hey guys
I just got into R/C cars and I have a few questions
1. I know that there are different types of nitro fuel such as 10%, 20%,30%. What do those percentages mean and what is the best to run?
2. From what I understand, if I have a gear with a lot of teeth, I should get more top end. If I have a gear with less teeth, I would get more acceleration, but less top end. Is this right?
Joe
Posts: 10,555
Threads: 465
Joined: May 2005
Reputation:
0
Chicagojoe Wrote:Hey guys
I just got into R/C cars and I have a few questions
1. I know that there are different types of nitro fuel such as 10%, 20%,30%. What do those percentages mean and what is the best to run?
2. From what I understand, if I have a gear with a lot of teeth, I should get more top end. If I have a gear with less teeth, I would get more acceleration, but less top end. Is this right?
Joe
Hey, welcome to the forum. 
The percentage is of nitromethane content. Nobody that I know runs 10%. The higher the percent, the more power you'll get, but it'll also shorten engine life (not very noticeably though). I run 30% and so do many others, and some even have ran 40%.
There's always 2 gears, one directly connected to the motor/engine (the pinion or clutch bell) and one that the pinion or clutch bell spins, called the spur gear.
You're right on the gear thing, as long as it's the "pinion" or "clutch bell" (pinion on electric, clutch bell on nitro)(smaller gear of the two). If you went up on teeth on the spur gear (the bigger in size gear of the two), you'd get more low end. If you go down on the spur gear, you get more top end.
Matt
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Posts: 23
Threads: 7
Joined: Jul 2006
Reputation:
0
Revo2k Wrote:Hey, welcome to the forum.
The percentage is of nitromethane content. Nobody that I know runs 10%. The higher the percent, the more power you'll get, but it'll also shorten engine life (not very noticeably though). I run 30% and so do many others, and some even have ran 40%.
There's always 2 gears, one directly connected to the motor/engine (the pinion or clutch bell) and one that the pinion or clutch bell spins, called the spur gear.
You're right on the gear thing, as long as it's the "pinion" or "clutch bell" (pinion on electric, clutch bell on nitro)(smaller gear of the two). If you went up on teeth on the spur gear (the bigger in size gear of the two), you'd get more low end. If you go down on the spur gear, you get more top end.
Matt
Thanks for the info
Posts: 10,555
Threads: 465
Joined: May 2005
Reputation:
0
Yep. No problem.
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Posts: 2,332
Threads: 88
Joined: Jul 2004
Reputation:
0
Revo2k Wrote:The higher the percent, the more power you'll get, but it'll also shorten engine life (not very noticeably though). I run 30% and so do many others, and some even have ran 40%.
I would have to disagree with you on this one. I have been running 40% for just over 2 years now, and have only had ONE engine die prematurely. This wasn't at all related to the Nitro content, it was die to a bad weld on a Trinity pipe causing an air leak.
I will agree that Higher nitro %'s are a little less forgiving with tuning, and CAN shorten engine life if not tuned right. As long as you have a good tune, the higher nitro's are fine. I definatlety wouldn't recommend it to someone just getting into the hobby though. Start with a lower Nitro % ( minimum of 20%), and develop your tuning. Once you are confident in your tuning, then you can go up to higher % "Race" fuels.
I'll keep my God, my freedom, my guns, and my money. You can keep "THE CHANGE."
Posts: 10,555
Threads: 465
Joined: May 2005
Reputation:
0
thenewguy821 Wrote:I would have to disagree with you on this one. I have been running 40% for just over 2 years now, and have only had ONE engine die prematurely. This wasn't at all related to the Nitro content, it was die to a bad weld on a Trinity pipe causing an air leak.
I will agree that Higher nitro %'s are a little less forgiving with tuning, and CAN shorten engine life if not tuned right. As long as you have a good tune, the higher nitro's are fine. I definatlety wouldn't recommend it to someone just getting into the hobby though. Start with a lower Nitro % ( minimum of 20%), and develop your tuning. Once you are confident in your tuning, then you can go up to higher % "Race" fuels.
^^^Listen to him lol... I was just going off what I thought I heard but could be wrong lol...
Tekno EB48.4 HobbyWing XR8 Sanwa M12
Posts: 23
Threads: 7
Joined: Jul 2006
Reputation:
0
thenewguy821 Wrote:Start with a lower Nitro % ( minimum of 20%), and develop your tuning. Once you are confident in your tuning, then you can go up to higher % "Race" fuels.
Right now I am running 20% but only because thats what came with it when i bought it.
Posts: 2,332
Threads: 88
Joined: Jul 2004
Reputation:
0
Chicagojoe Wrote:Right now I am running 20% but only because thats what came with it when i bought it.
That's perfect for starting out. Get used to tuning it, pay attention to how it performs when tuned right and how it sounds. When it starts acting differently, pay attention to what it is doing. Listen to the RPM's, is it bogging or cutting out, etc. and make your adjustments. As you are more confident with how well you can "read" what the engine is telling you, then you can decide if you want to stick with 20% or go higher.
I'll keep my God, my freedom, my guns, and my money. You can keep "THE CHANGE."
Posts: 2,332
Threads: 88
Joined: Jul 2004
Reputation:
0
Here's a quick video on tuning. It was made by HPI, but it will show how to distinguish what the different engine sounds are telling you.
Engine tuning
I'll keep my God, my freedom, my guns, and my money. You can keep "THE CHANGE."
Posts: 3,634
Threads: 181
Joined: Oct 2004
Reputation:
0
A friend will help you move, but a REAL friend will help you move a body.
|
