Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
New Revo engine option
#76
Still feel bad about that bro... Hopefully you sent it back and got a new one to sell...
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#77
speaking of revo smallblock options, don't get the 3.3. Maybe try this new SH 2.5 but don't waste your money on a motor that will just blow up within a SHORT XXX amount of time.

My 3.3 blew a rear bearing and the rod. I know how to tune, speaking of that, Michowski, I tune your motors because you need help. Also me and you were side by side down the strait in STL with the 3.3's....This EBTZ I have now is faster, I'll take you up on the drag race, or track race whatever Smile
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#78
you never tuned my 3.3, and bobo had a tz at stl and he couldnt pass me and I couldnt pass him. His was modded to i think.
[Image: mich1iy1.jpg]
Reply
#79
yeah im getting so sick of these dang traxxas motors. i was at the track and my truck was super rich to where it bogged a little and it was hitting 300*....andf i took the temp with an $80 temp gun. so its not the temp gun

I dont know if its ok to drive your omtor when its hitting 300 with plenty of smoke or not?? maybe i have an air leak but i doubt it
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#80
Tune for performance and smoke... Not temp
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#81
well just cuz ur temp gun says 300 dont mean chit, 80$ or not it could be wrong....you need to tune by sound and "feel" this isnt the easiest thing in the world. make sure you have a good steady idle and that the low end is snappy but will load up after 20 seconds or so and when u are at WOT make sure that it isnt starving for fuel or whinning out...make sure there is good smoke at full throttle and throughout the whole powerband. if it temps at 300* runs well and has good smoke just leave it
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#82
Yeah... My Novarossi 528 3 port will not run (literally) below 250-260


And thats with an extregen(sp?) gun ... AKA the best...

After a hard run main temps in the 290's+ dont surprise me... But it has power and smoke... Starts ,idles and screams ... So screw the temps!
Dont mess wit my sig Line tune!
--Then follow the rules! haha!-- -Tune
Reply
#83
yeah well i just have gotten so reliable to tuning by temps........but, I know why i was running so hot....my gasket was torn and forming an air leak.
[Image: 100_2084Medium.jpg]
[Image: 100_2080Medium.jpg]
[Image: 100_2079Medium.jpg]

so I put a new one on.......lol
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#84
is that really an air leak? serious question lol

tuning by temp is probably the worst way to tune, use temps as a reference point more than a tuning aid
Here is a link to my website-
http://www.czech-it-out-graphics.com
1/29/07 never forget....TTT Confusedalute:
Bringing old know-it-all blow hards back to reallity at a forum near you

"Always Imitated, Never Duplicated"
Reply
#85
well its not really an air leak....but what its doing is the pipe maniflod is not making a direct contact to the engine with that on, nd when I had the body off i revved the engine, and I had smoke coming out of the exhaust pipe and where the exhaust manifold or header attaches to the motor.

yeah i tune mainly by feel and sound, but lately i have been really worried about temps, but like rocco said, screw 'em
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply
#86
an exhaust leak is almost as bad as a carb leak when it comes to running hot and tuning issues.
Mugen MBX5T
RBS5
RB2045
Futaba 3PM
Hitec 5955, 5965
Reply
#87
yeah, luckily it was only for about a tnak and i took the cooling head off and the piston looks fine.......its kinda an oarngish color with a faint brown "c"
Losi 8ight with v-spec[SIZE="4"]
[/SIZE]
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  trx 3.3 engine problem help please? gregk20 1 2,978 08-11-2010, 08:02 PM
Last Post: Traxxas_Junkee
  question about a vspec engine eraser 83 17,052 02-06-2008, 04:36 PM
Last Post: J-Dub
  Cold weather engine tune rcrunr1 5 2,942 01-25-2008, 06:15 PM
Last Post: J-Dub
  cleaning engine internals AddictedtoNITRO 26 7,808 12-26-2007, 01:25 AM
Last Post: J-Dub
  Comprehensive engine dyno results mikeh 14 18,055 10-31-2007, 02:31 PM
Last Post: Czech-it-Out Graphics
  nitro tc3 engine suggestion hotrodlincoln 5 2,901 09-11-2007, 01:16 PM
Last Post: Tex
  Axial .32 vs. Traxxas Big Block Installation Kit Revo marcaotz 3 2,585 09-07-2007, 11:33 PM
Last Post: Tex
  Revo Pipe, Rubbing J-Dub 10 3,437 08-16-2007, 07:01 PM
Last Post: J-Dub
  Learning engine mods cr4sh_27 21 6,120 08-12-2007, 02:07 AM
Last Post: Thirdgen89GTA
  Big Block Revo Problems? No More! :D J-Dub 12 4,382 07-25-2007, 06:02 PM
Last Post: J-Dub

Forum Jump:


Users browsing this thread: 1 Guest(s)