Login

cheesecake · 04-23-2007, 02:48 PM

i cant keep it idleing it just dies im not sure what the problem is it was running good then whenever i hit the breaks or slow down to a stop it would die. oh well time for a new engine any ideas its for a 1/10 truck

~~Meatwad~~ · 04-23-2007, 02:49 PM

goat 585 has 2 hpi 12s for $75

**DAVEC-NITRO-RS4** · 04-23-2007, 02:54 PM

Check your clutch and clutch bell bearings. If they hang up, it's just like snubbing the flywheel to a stop.

UE-Maxx · 04-23-2007, 02:57 PM

Also check your idle. It might be too low.

cheesecake · 04-23-2007, 02:58 PM

ill look into that
im going to tear the truck apart tommarow. i took it apart last night and rebuilt it and i went to test ti and the problems happend

cheesecake · 04-23-2007, 03:02 PM

maybe the engine isnt sealed correctly could that be a problem also

UE-Maxx · 04-23-2007, 03:09 PM

Make sure everything is tight on the engine. Tighten down the head bolts in start pattern so they all get tightened evenly. Check the back plate and carb sinch bolt.

Traxxas_Junkee · 04-23-2007, 03:42 PM

If you rebuilt it, then that means that you just need to put the trim for your throttle servo so it won't move the carb when you hit the brakes, then you will need to turn your idle up on the carb.

cheesecake · 04-23-2007, 03:48 PM

DAVEC-NITRO-RS4 Wrote:Check your clutch and clutch bell bearings. If they hang up, it's just like snubbing the flywheel to a stop.

well you get the cookie when i put the clutch nut on i used threadlock and it seeped out and on the the bearings and the bell housing. who knows what breaks down threadlock and also when i got the nut off i destroyed the collet on the shaft so now i need to get everything that is stuck together apart and try it again.

im still going to order an extra motor i think there is more to it than what i just found

cheesecake · 04-23-2007, 05:01 PM

thanks guys i got everything freed up and now it runs decent i need to figure out why it runs so hot im in the 240-270 range and when i richen it up it still is hot

Traxxas_Junkee · 04-23-2007, 06:09 PM

Do you have a vent hole cut in the body? Geared to low?

HAGASAN · 04-23-2007, 06:12 PM

You buy this motor from Mikey? Wink

**rocco79** · 04-23-2007, 06:22 PM

lol

~~Rawkfist_02~~ · 04-24-2007, 10:21 AM

Why not bring your car up to Cary Illinois and Ill help fix it?

**Tex** · 04-24-2007, 12:45 PM

240-270 is ok

What king of crank shaft does your truck run? threaded crank (little stubby) or a longer pilot (SG) shaft?

slim · 04-24-2007, 01:45 PM

270 is totally fine... maybe a bit warm for a .12 tho on the other hand.

cheesecake · 04-24-2007, 01:57 PM

its the standard shaft its not the cut standard its the long threaded. but not the sg.

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Port and polished motor	Edward Rc	1	3,417	11-08-2009, 10:14 AM Last Post: DAVEC-NITRO-RS4
	2nd motor back from propinch	eraser	83	30,861	05-29-2008, 01:54 PM Last Post: Thirdgen89GTA
	eletric motor turns to RPM's..........	bob1961	4	5,672	03-28-2008, 08:24 PM Last Post: bob1961
	Which motor	hansarvin	134	27,733	01-23-2008, 11:25 AM Last Post: J-Dub
	question about a new motor	eraser	20	5,509	10-14-2007, 12:39 AM Last Post: willitbme15
	My new motor	rocco79	34	8,393	04-22-2007, 10:32 AM Last Post: Meatwad
	what motor?	AddictedtoNITRO	10	3,367	03-26-2007, 10:38 PM Last Post: HAGASAN
	2.5T electric motor?	Gforce	1	1,868	02-05-2007, 01:39 AM Last Post: Czech-it-Out Graphics
	elec motor	AddictedtoNITRO	14	3,991	10-23-2006, 11:48 PM Last Post: mikeh
	which motor??	kevinF	39	7,663	09-28-2006, 11:12 AM Last Post: kevinF