Kanai II Truggy Buildup

[rocco79]

My truggy was just as fast as my savage if not faster... I dont think a 2 speed adds that much on the top end... I think it just helps nitro engines build the torque they need down low with a lower ratio...

Im sure if you got those boas on youd be fine

[cemeb4dk]

Assuming you have a 46 tooth spur (stock kyosho) and a 16 tooth bell you are running a 2.8 ratio. Thats about 1.5 too low for runnign mt tires... I hope you have another $70 for a new clutch soon. Because you are going to smoke the clutch and over work your engine.....

But then again what do I know....LOL

[snakebite46]

But then again what do I know....LOL

Well let's see.

1. You know where to shop for big hats.
2. You know how to get mad over someone leaving your sharpie out.
3. You know how to make R/C purchases without the wife knowing.
4. You know how to ride your tri-cycle when your drunk.
5. You know how to lay the power down !!!
6. You know how to embalm some fresh meat.

[Czech-it-Out Graphics]

Lmao

[cemeb4dk]

Laughing my ass off....

Good to have you back....

Using that as my sig line...

[Ponch]

Assuming you have a 46 tooth spur (stock kyosho) and a 16 tooth bell you are running a 2.8 ratio. Thats about 1.5 too low for runnign mt tires... I hope you have another $70 for a new clutch soon. Because you are going to smoke the clutch and over work your engine.....

But then again what do I know....LOL

Nuh unh!!! I got me some LSP ring and pinion gears so I can run this chit dude...:p:

[cemeb4dk]

LOL
That is the rario at your clutch.

Ask how many LSP drivers are running a 16t bell, and I bet zero. And we have your ring and pinions and a larger spur gear... I have a NR 528 and the most I ever ran was a 15.

But like I said before what do I know, just trying to save you some aggrevation but you obviously know more.... 8^)

So good luck!!!!!!!

[Ponch]

LOL
That is the rario at your clutch.

Ask how many LSP drivers are running a 16t bell, and I bet zero. And we have your ring and pinions and a larger spur gear... I have a NR 528 and the most I ever ran was a 15.

But like I said before what do I know, just trying to save you some aggrevation but you obviously know more.... 8^)

So good luck!!!!!!!

Alright then... You are talking about running a 15t with regular sized tires though, right? Right now all I have to run is the komodo LP's and they're tiny.

[Racin' Ranger1]

when u go to the track get some vid of that thing.

[Ponch]

If I remember to. We're rolling up there around 6 and I want to run as much as possible before sundown.

[kevinF]

yeah if you do video tape it make sure you POST IT UP... lol

[Ponch]

Hey, my foams came in! My boas are all glued up and ready to run tonight.

If I do take video, I'll post it up.

[Ponch]

Uh-oh. I had a run away. Got about 40ft and then re-gained power. Thankfully, it jumped a little curb and ended up in a person down the street's lawn, about a foot away from their SUV tire. That could have been bad. I don't know what could have went wrong though, everything that should be loc-tighted is, all plugs are secure in the receiver, and there's no binding w/ the servos in motion. Ideas? It ran fine afterwards, no glitches or anything.

Do you think that mabye the metal gears (clutch and spur) are causing interference?