2nd motor back from propinch

[chris arnold]

i dont think so mick.

[eraser]

then stick to your clamp and stove lmao

[Ponch]

then stick to your clamp and stove lmao

He wasn't replying to you, he was replying to Mike's post a few posts up.

[rocco79]

Not too sound rude...

But how about ya take some pics of his work.... You keep sayin how sweet it is, now id like to see it with my own two eyes

[chickenfarmer3]

+ 123456789

[HAGASAN]

Rocco, just send in your Axial .38 and see for yourself. Im about ready to send in my Racers Edge .32 soon.

[chickenfarmer3]

i sent a pair of my STS .28's.....we will see how his dremel does on those.....

[pwnzor]

no doubt, open one up and show the mods, I would like to see

[rocco79]

Lmao

[blktransam]

the site has no info on the "modding" I tried to call him with no luck I left a message and will call again tommarow as I need my engine pinched prior to the next pro series race which is in about a week and half

[Czech-it-Out Graphics]

osrocket...

[blktransam]

yeah I used osrocket like 2 yrs ago with good luck, I just like trying new people/things

[rocco79]

no pics on site at all

[motoxer4life]

so what exactly is pinching? ive been reading this thread and never got what it was.

[rocco79]

a process that can in take a motor that is worn out and lacks compression and renews it and adds a couple gallons to the life of the motor....

As long as the sleeve and pistion dont have gouges or serious blems most worn p/s will benefit from a pinch ...

I think you can only pinch a motor like 3 times though

[Czech-it-Out Graphics]

shit u can pinch a motor for ever, run it till it blows baby!!!

[kevinF]

so what exactly is pinching? ive been reading this thread and never got what it was.

they basically make the top of the sleeve a tighter fit so it has more compression

[chris arnold]

hell czech had an rb that jimmy pinched so many times its only an 18 now.
i think im gonna send this guy my cen 46, is that legal for 1/8 buggy at that pro series yall talk about

[rocco79]

Zing!!!

[blktransam]

never recieved a call back from them today... thats strike one in my book

[J-Dub]

Might as well just buy the new reciprocating assembly. ( P/S. Conrod Wristpin and Clip)

At least that's what I'd do...but I guess that's expensive.

Would you say you racers pinch your 'expensive' motors a couple times instead of rebuilding them?

[Czech-it-Out Graphics]

yea cuz its stupid to rebuild it cuz it cost about as much as a brand new one so why bother

[blktransam]

I wanted him to modd mine as well though...

[J-Dub]

yea cuz its stupid to rebuild it cuz it cost about as much as a brand new one so why bother

After the life of the engine is done...do you then rebuild it after it;s been pinched? I've not gone through many motors, Im just curious what you would do.

[Czech-it-Out Graphics]

not many do, alot of times if you are sponsored you can send in your used shit an they will rebuild it for you either for free or pretty cheap. But when my dad had the access to the machines to do pinching i pinched them light until they just didnt run as well. At that point most of my motors had 10 gallons on them so they were for parts or to sell with a roller on ebay. Usually the bearings are good and the case is always good to have for back up etc. pinching is pretty much ur best bet, break it in again (lightly) then after about a gallon or so throw in a new rod and it will last you a long time